$699.00(USA and Canada only)
The SNAP-AIRTD-8U analog input module provides 8 input channels, each individually software configurable. This module is commonly used for 3-wire RTD temperature inputs but is also suited to high-resolution resistance measurements. It features open circuit detection if any wire breaks.
You can individually configure each of the module's 8 points for a variety of behaviors, including a fixed temperature range for nickel, platinum, or copper RTD inputs; a fixed range in ohms; or two types of auto-ranging where the module scrolls within a range (in ohms) and chooses the best resolution.
SNAP-AIRTD-8U在顶部有一个插件端子,并带有弹簧钳连接器,可轻松接线。盒子中提供了一个带有模块的插入工具。
所有8个输入共享相同的参考终端。确保使用隔离的RTD探针。
SNAP-AIRTD-8U需要使用固件R9.5A或更高的SNAP PAC Brain或R系列控制器。该模块不能与传统的大脑或控制器一起使用。
snap-airtd-8U
3线RTD输入和最大温度表范围(实际范围取决于您的探针)
1000 ohm platinum @ 0 °Cα= 0.00385Range: -200 to 850 °C(-328至1,582°F)
100 ohm platinum @ 0 °Cα= 0.00385Range: -200 °C to 850 °C(-328至1,582°F)
10 ohm copper @ 25 °Cα= 0.00427Range: -60 to 355 °C(-76 to 671 °F)
1000欧姆镍 @ 0°Cα= 0.00618范围:-60至170°C(-76 to 356 °F)
100欧姆镍 @ 0°Cα= 0.00618Range: -60 to 250 °C(-76至482°F)
1000 ohm nickel @ 70 °Fα= 0.00637Range: -46 to 148.9 °C(-50至300°F)
120欧姆镍 @ 0°Cα= 0.00672Range: -80 to 260 °C(-112 to 500 °F)
输入范围
0至4000欧姆
0to 400 ohms
0至40欧姆
Accuracy来自工厂After setting gain and offset
0.8°C(PT);0.6°C(Ni)0.6°C(PT);0.4°C(Ni)
1.7 °C1.2 °C
激发电流
0.325 MA
2 ma
4.28 mA
Over-Range Limit
10% overrange for all measurements in ohms
Resolution在欧姆在RTD温度中
The greater of: (Ohms Range / 100,000) or 1 milliohm
优于或等于0.05°C(0.09°F)
输入过滤Front end filteringDSP Notch filter
-15 dB @ 50 Hz, -20 dB @ 60 Hz
20 Hz(-3 DDB = 5.24 Hz)
Data Freshness (Max)
1.2 s
自动范围定居时间
步骤从10到8000
步骤从8000变为10
1.2 sto the next higher or lower range
<= 10 s范围(频道可能显示超级范围直到解决)
<= 10 s ranging down (channel will give a reading while settling)
总铅电阻
最大200欧
DC共同模式拒绝
> -120 dB
交流通用模式拒绝
> -120 dBat 60 Hz
Maximum Survivable Fault Voltage at Input (between any 2 field wires)
±8 V
最大运行通用模式电压
250 V场终端到逻辑连接器
Isolation
1500 V field side to logic side
Power Requirements
5.00至5.20 VDC @ 135 ma
Operating Temperature
-20°C至70°C
储存温度
-40 °C to 85 °C
湿度
5-95%, non-condensing
最大电线尺寸
20 AWG
Torque, hold-down screws
Not to exceed 1 in-lb (0.11 N-m)
代理商批准
UL,CE,ROHS,DFARS;UKCA
保修单
寿命
SNAP I/O analog input modules are part of Opto 22's SNAP PAC System. This document includes descriptions, specifications, and wiring and dimensional diagrams for the following analog input modules:
This document is the Manufacturer's Declaration of Conformity for the products listed herein, in accordance with the rules, regulations and standards of the United Kingdom. The models cited have been tested to the essential requirements listed in the Standards section, and fully comply with the legislation as listed in UK Legislation section.
This document is the Manufacturer's Declaration of Conformity for the products listed herein, in accordance with European, international, and/or national standards and regulations.
该文件是遵守欧盟指令2015/863/欧盟的陈述,限制有害物质(ROHS 3)。本文档列出了符合ROHS 3指令的物质限制的Opto 2德赢下载2产品。
本文档列出了具有承销商实验室(UL)批准的所有Opto 22零件号。
This document is the Manufacturer's Declaration for the listed products as mentioned in the attachment - to which this confirmation refers - that they are in accordance with the mentioned European, international and/or national standards and regulations.
This CAD file includes the drawing of thesnap-airtd-8U模块。每个模块都提供通道到通道的隔离。
此概述描述了SNAP PAC系统的四个集成组件:软件,控制器,大脑和I/O。该硬件和软件系统专为工业控制,远程监控和数据采集而设计。
A quick tip on spring clamps.